Titatech Engineering Sdn. Bhd.

Anvil BEAM CLAMPS Fig. 228 Universal Forged Steel Beam Clamp with UFS (Upper) Nut Right-Hand Thread

Material: Forged steel
Finish: Plain or Zinc Plated
Service: For suspension of heavy loads from beams withflange widths up to 15" and flange thickness to 1.031.
Approvals: Complies with Federal Specification A-A-1192A(Type 28 without links; Type 29 with links), WW-H-171-E (Type 30 & 31),ANSI/MSS SP-69 and MSS SP-58 (Type 28 without links; Type 29 with links).
Installation: Fit jaws over edges of lower beam flange and tighten nutson tie rod to lock clamp in place.
Features:• Upper nut is tapped to any specified size up to the maximum rod size.• Quickly, easily, economically installed.• Tie rod insures a tight non-slip fit to the beam.• Clamps are available, tapped to any specified rod size up to themaximum rod size.
Ordering: Specify clamp size, figure number, name, rod size and finish.

Size Range: 1⁄2" through 2 1⁄4"
Material: Carbon steel
Finish: Plain or Hot-Dip Galvanized
Service: For single rod suspension of Fig. 81-H, type B and C constant supports.
Ordering: Specify rod size, figure number, name, finish and “H” dimension.

Size Range: 3⁄8" to 3 3⁄4“
Material: Carbon steel
Finish: Plain or Hot-Dip Galvanized
Service: A heavy duty washer plate used on top of channels or angles forsupporting pipe with rods or U-bolts.
Maximum Temperature: Plain 750° F, Galvanized 450° F
Ordering: Specify rod size, figure number, name and finish.

Size Range: 3⁄8" through 5⁄8"
Material: Malleable iron
Finish: Plain or Hot-Dip Galvanized
Service: Recommended for attachment to steel or wooden beams, etc.
Approvals: Complies with Federal Specification A-A-1192A (Type 34)WW-H-171-E (Type 35), ANSI/MSS SP-69 and MSS SP-58 (Type 34).UL, ULC Listed and FM Approved (Sizes 3⁄8" for use on woodenand steel beams and 1⁄2" for use on steel beams).
Features: An economical, practical and adjustable means of securing hangersto beams, etc.
Ordering: Specify rod size, figure number, name and finish.

Size Range: 3⁄8" through 5⁄8"
Material: Carbon steel
Finish: Plain or Zinc Plated (Hot-Dip Galvanized optional)
Service: Clip can be fastened to side of joist or wall to support hanger rod.
Approvals: Complies with Federal Specification A-A-1192A (Type 34), WW-H-171-E (Type 35)and ANSI/MSS SP-69 and MSS SP-58 (Type 34). UL Listed and FM Approved (steel beam only).
Ordering: Specify rod size, figure number, name and finish.

Size: 3⁄8"
Material: Pre-Galvanized Steel
Service: Attachment to structure to connect threaded hanger rod.Approvals: UL and ULC Listed, and FM Approved.
Installation:• Thread rod completely into hanger. Secure rod by tightening jamnut against bottom of hanger.• Secure hanger to structural member with recommended fasteners.
Features:• Pre-formed threads for easy rod assembly.
Ordering: Specify rod size, figure number and name.

Size: 3⁄8"
Material: Pre-Galvanized Steel
Service: Attachment to structure to connect threaded hanger rod.
Approvals: UL and ULC Listed, and FM Approved.
Installation:• Thread rod completely into hanger. Secure rod by tightening jamnut against bottom of hanger.• Secure hanger to structural member with recommended fasteners.
Features:• Pre-formed threads for easy rod assembly.• Off-set angle provides unlimited vertical adjustment.
Ordering: Specify rod size, figure number and name.

Material: Carbon steel
Finish: Plain or Hot-Dip Galvanized
Service: Recommended for support from below or above bracket.
Approvals: Complies with Federal Specification A-A-1192A (Type 31),WW-H-171-E (Type 32), ANSI/MSS SP-69 and MSS SP-58 (Type 31).FM Approved when used with 3⁄8" rod, 3⁄4" - 4" pipe sizes & 1⁄2" rod,5" - 8" pipe sizes.
How to size: Determine bracket size by dimension of standard bracket mostsuitable to the installation.
Installation: When bolted to a wall, an additional back plate may be requiredof such thickness and size as to properly distribute the weight over the wall.Size and thickness of the back plate is governed by the load to be carried andthe nature and conditions of the wall. Back plates furnished upon request.
Features:• Bracket may be installed either in position illustrated or reversed.• Ends of bracket are drilled to accept hanger rods up to 3⁄4".
Ordering: Specify bracket number, figure number, name and finish.

Size Range: 3⁄8" and 1⁄2"
Material: Plastic
Service: Recommended for giving a finished appearance where rod enters ceiling.
Installation: Slide plate up rod until flush against ceiling.
Features:• Highly economical• Quickly installed• Held firmly to rod by design and friction
Ordering: Specify rod size, figure number, name. (rod not included)

Size Range: 3⁄8" through 3⁄4"
Material: Malleable iron
Finish: Plain
Service: Recommended for suspension of pipe lines or conduit fromlevel ceilings.
Approvals: UL, ULC Listed and FM Approved (Sizes 3⁄8" and 1⁄2").
Installation: Flange size 3⁄8" has two holes, sizes 1⁄2", 5⁄8", and 3⁄4"have three holes.
Features:• Provides vertical adjustment up to 1".• Good appearance.
Ordering: Specify rod size, figure number and name.

Size Range: 1⁄2" through 8"
Material: Cast iron
Finish: Plain or Zinc Plated (Hot-Dip Galvanized optional)
Service: Gives finished appearance where pipe enters ceiling.
Installation: Sizes 1⁄2" to 4" furnished with one machine screw;sizes 5" to 8", two machine screws.
Ordering: Specify pipe size, figure number, name and finish.

Size Range: 3⁄8" through 7⁄8"
Material: Malleable iron
Finish: Plain
Service: Upper attachment for suspending pipe from a concrete ceilingwhere no lateral adjustment is required.
Approvals: UL, ULC Listed and FM Approved.
Features:• Eliminates the necessity of drilling holes in wooden forms.• Reduced overall height and four slots for nail attachment gives stabilityto the insert while the concrete is being poured.
Ordering: Specify rod size, figure number and name.