Anvil CONCRETE INSERTS & ATTACHMENTS Fig. 282 Universal Concrete Insert
- Size Range: 3⁄8" through 7⁄8"
- Material: Malleable iron body and nut
- Finish: Plain or Zinc Plated (Hot-Dip Fasteners Not Available)
- Service: Upper attachment for suspending pipe, shafting, motors and similarequipment from a concrete ceiling; especially suitable where rod sizes cannot bereadily determined in advance.
- Features:• Cast body prevents concrete seepage.• Opening in top of insert provides for use of reinforcing rods up to 7⁄8" diameter. Sidesof insert are recessed for reinforcing rods up to 1" diameter.• Low height, broad flat bottom and widely separated nail slots minimize displacementduring construction.• The nut, held in place by V-type teeth on both insert and nut, can be raised and movedfrom side to side providing for lateral adjustment.• Rod is locked in place by screwing it firmly against the top of the recess.• One body size.
Anvil CONCRETE INSERTS & ATTACHMENTS Fig. 284 Metal Deck Hanger
- Size Range: 3⁄8" through 3⁄4"
- Material: Carbon steel
- Finish: Plain
- Service: Recommended for suspending pipe or conduit in metalconcrete deck forms for a variety of rod sizes. May be used with a rodcoupling such as the Fig. 135 or 136 to allow for extended rod lengths.
- Features:• L and H can be specified for a custom fit if your particular deck doesnot accommodate type A, B, or C.• Standard 6" long UNC bolt is welded to bracket to ensure assemblyremains intact during shipment.
- Ordering: Specify Figure 284, design type (A, B, C) and bolt diameter.If your specific deck will not fit one of the design types and/or a differentbolt size is required, specify leg height (H), opening (L) and bolt size.FIG
Anvil CONCRETE INSERTS & ATTACHMENTS Fig. 47 Concrete Single Lug Plate
- Size Range: 1⁄2" through 2"
- Material: Carbon steel
- Finish: Plain or Hot-Dip Galvanized
- Service: Structural attachment to concrete ceiling lug is usedin conjunction with Fig. 299 (see page 103) forged steel clevisand anchors of sufficient strength to hold the desired load.
- Ordering: Specify rod size, figure number, name and finish.
Anvil HANGER RODS Fig. 146 Continuous Threaded Rod
- Size Range: 1⁄4" through 1 1⁄2" Stocked in six, ten, and twelve footlengths. Other even foot lengths can be furnished to order.
- Material: Carbon steel or Stainless Steel Gr 304
- Threads: National Coarse (USS), rod threaded complete length.
- Finish: Plain or Zinc Plated (Hot-Dip Galvanized optional)
- Maximum Temperature: 650° F
- Ordering: Specify rod diameter and length, figure number,name and finish
- Note: The acceptability of galvanized coatings at temperaturesabove 450°F is at the discretion of the end user.
Anvil HANGER RODS Fig. 148 Rod with Eye End
- Size Range: 2 3⁄4" through 5"
- Material: Carbon steel
- Finish: Plain or Zinc Plated (Hot-Dip Galvanized optional)
- Service: A large diameter rod with eye end for load ratings thru 184,000 pounds.
- Ordering: Specify rod size, figure number, name, finish and “L” dimension. Indicateif desired thread length is other than standard.
- Note: The acceptability of galvanized coatings at temperatures above 450°F is at thediscretion of the end user.
Anvil ROD ATTACHMENTS Fig. 114 Turnbuckle Adjuster
- Size Range: 1⁄4" through 3⁄4"
- Material: Malleable iron
- Finish: Plain
- Installation: Normally used with split pipe ring, Fig. 108, see page 36.
- Approvals: Complies with Federal Specification A-A-1192A (Type 15),WW-H-171-E (Type 15), ANSI/MSS SP-69 and MSS SP-58 (Type 15).
- Maximum Temperature: 450° F
- Features:• An economical and simple means of obtaining verticaladjustment and flexibility at the pipe connection.• Permits adjustment after pipe is in place.
- Ordering: Specify rod size, figure number and name.
Anvil ROD ATTACHMENTS Fig. 299 Forged Steel Clevis
- Size Range: 3⁄8" through 4"
- Material: Forged steel
- Finish: Plain or Zinc Plated (Hot-Dip Galvanized optional)
- Service: For use on high temperature piping installations.
- Approvals: Complies with Federal Specification A-A-1192A (Type 14), WW-H-171-E (Type 14),ANSI/MSS SP-69 and MSS SP-58 (Type 14).
- Features:• Available with pin and cotter pins, if required.
- Ordering: Specify rod size, figure number, name and finish. If pin and cotter pins are required,specify “with pin”. If other than standard combination of clevis number and rod size is required,specify clevis number, special rod tapping size, pin size, grip.
- Note: The acceptability of galvanized coatings at temperatures above 450°F is at the discretion of the end user
Anvil BOLTS, NUTS, PINS & U-BOLTS Fig. 291 Clevis Pin with Cotters
- Size Range: 1⁄2" through 4"
- Material: Carbon steel
- Finish: Plain or Zinc Plated (Hot-Dip Galvanized optional)
- Maximum Temperature: 650° F
- Service: For use with type C variable spring hanger, type C constantsupport (Fig. 81-H only) and Fig. 66 welded beam attachment.
- Ordering: Specify pin diameter, figure number, name, finish andif cotter pins are required.
- Note: The acceptability of galvanized coatings at temperatures above450°F is at the discretion of the end user.
Anvil BOLTS, NUTS, PINS & U-BOLTS Machine Bolts
- Size Range: American Standard hexagon head bolts with AmericanStandard hexagon nuts are stocked in sizes 3⁄8" through 1 1⁄8"UNC thread series. Other sizes are available upon request.Lengths of bolts are measured from under head to extreme point.
- Finish: Plain or Electroplated
- Ordering: Specify bolt size, name and length.
Anvil BOLTS, NUTS, PINS & U-BOLTS Fig. 137C: Plastic Coated U-Bolts
- Size Range: 1⁄2" through 8"
- Material: Carbon steel U-bolt and four finished hex nuts. Formed portion of the U-boltis plastic coated.
- Maximum Temperature: 225° F
- Service: Recommended for support or guide for glass, copper, brass and aluminum pipe.
- Approvals: Complies with Federal Specification A-A-1192A (Type 24), WW-H-171-E (Type 24),ANSI/MSS SP-69 and MSS SP-58 (Type 24).
- Ordering: Specify pipe size x rod size (e.g., 2 x 3⁄8), figure number and name.If hex nuts are not required, specify “without hex nuts”
Anvil STRAPS Fig. 262 Strap Short
- Size Range: 1⁄2" through 4"
- Material: Carbon steel
- Finish: Plain or Zinc Plated (Hot-Dip Galvanized optional)
- Maximum Temperature: 650° F
- Approvals: Complies with Federal Specification A-A-1192A (Type 26), WW-H-171-E (Type 26),ANSI/MSS SP-69 and MSS SP-58 (Type 26).
- Ordering: Specify pipe size, figure number, name and finish.
- Note: The acceptability of galvanized coatings at temperatures above 450°Fis at the discretion of the end user.
Anvil STRAPS Fig. 243 Pipe Strap
- Size Range: 1⁄2" through 6" pipe
- Material: Carbon steel
- Finish: Plain
- Service: Restraint of pipe in specified direction whilepermitting movement in non-restrained direction.
- Maximum Temperature: 650° F
- Ordering: Specify figure number, name, and pipe size.Larger sizes available upon request.
