Hazardous Duty™ Division 1 Explosion Proof
- 10:1 Variable torque, 2:1 Constant torque
- 1.15 Service Factor• Class F insulation
- Meets temperature code T2A
- All Cast iron construction
- Shaft slinger
- External surface treated with epoxy paint
- Name plated 60/50 Hz, 190/380 Volts, at next lower HP
- See modification section for addition of C-Face kits (254T-445T)
- Ball bearings (except as noted)
- UL Listed File No. E12044
- CSA Certified File No. LR47504
- Two year warranty
Inverter (Vector) Duty: microMAXTM
- Designed to replace PMDC motors (when used with a VFD)
- Constant horsepower to twice base speed (RPM)
- Class H insulation with CR200 magnet wire
- Removable base for C-Face footless mounting, as noted
- Continuous duty at 40ºC ambient
- Quick Connect terminal board, as noted
- Top mounted conduit box found on PMDC motors
- Eliminates brush and commutator maintenance
- UL Recognized, CSA Certified, and CE Mark
- Three year warranty
Inverter (Vector) Duty: Black Max® Hazardous Duty™
- MAX GUARD® Class F insulation system
- Constant torque operation from 0 to base speed on vector drive
- Constant HP operation to twice base RPM
- Continuous duty at 40ºC ambient
- Optimized for operation with IGBT inverter (NEMA Design A)
- Normally closed thermostats (one per phase, Class F)
- Ball Bearings
- Top mount (F3) conduit box included, shipped loose
- No Encoder Provisions provided
- Meets temperature code T3B
- UL listed, under file #E12044
- CSA certified, under file numbers LR47504 and LR21839
- Three year warranty
Inverter (Vector) Duty
- BEI H38 explosion proof encoder 1024 ppr, Class I Groups C & D,Class II Groups E, F, G included
- MAX GUARD® Class F insulation system
- Constant torque operation from 0 to base speed on vector drive
- Constant HP operation up to twice base speed
- Continuous duty at 40ºC ambient
- Optimized for operation with IGBT inverter (NEMA Design A)
- Normally closed thermostats (one per phase, Class F)
- Ball Bearings
- Cast iron frame and brackets
- F1 standard, NOT field reversible to F2
- UL Listed File No. E12044, MC228275
- CSA Certified File No. LR47504, MC236833
- Meets temperature code T3B
- Three year warranty
Washdown, DC Permanent Magnet SCR Rated, Totally Enclosed C-Face Footed (Removable Base)
- Class F insulation
- NEMA C-Face with removable rigid base
- Oversized brushes for extra long life
- Doubled sealed, oversized ball bearings
- Corrosion resistant 303 stainless steel shaft
- “V” ring Forsheda seals• High temperature, moisture resistant lubricant
- Exterior and interior components protected with enamel & polyester
- Stainless steel nameplate
- USDA approved white epoxy paint
- UL Recognized and CSA Certified
Brake Motors, Single Phase Totally Enclosed, C-Face Footed (Removable Base)
- Fail-safe, spring set Stearns 56 Series brake for holding or stopping
- Brake has manual wear adjustment for longer pad life
- Manual release lever on rear of brake housing
- Brake leads are terminated at the brake
- Universal mounting, no modifications needed
- Brake coil voltage matches motor voltages, see mod section for other brake coils
- Ball bearings, mechanically locked on shaft end
- 1.15 Service Factor (1.0 Service Factor as noted)
- Nameplated 60/50 hertz at next lowest horsepower
- UL Recognized and CSA Certified
Farm Duty / Agriculture, High Torque Single Phase, TEFC
- Ball bearings, shaft end mechanically locked on C-face models (excludes 5K models)
- 1.15 Service Factor (except as noted)
- Capacitor start design for high starting torque
- Capacitor start/capacitor run design for higher efficiency, as noted
- Low temperature manual reset thermal protector
- Totally enclosed and fully gasketed construction for dirty environments
- Condensate drains
- Shaft slinger
- UL Recognized and CSA Certified
Farm Duty / Agricultural Single Phase, TEAO, Direct Drive-Thru Bolt
- Economical split phase design
- X909 has1/2” diameter x 1.5” long shaft with flat
- X910 and X911 have 1/2” dia. X 2-1/2” long shaft with two flats, 90 degrees apart
- Thermal protection, as noted
- Ball bearings
- Fully gasketed
PowerWash™ XT Washdown Duty, Three Phase White Epoxy, Totally Enclosed
- 10:1 Variable torque, Constant torque speed range as listed below
- MAX GUARD® Class F insulation system
- 1.15 Service Factor on sinewave, 1.0 Service Factor on IGBT power
- Double sealed ball bearings
- 303 Stainless steel shaft with spring loaded contact seals in each end shield(Drive end only on TENV motors)
- Stainless steel conduit box cover, nameplate, fan guard (TEFC only)and hardware
- Cast oversized conduit box with high temperature nitrile gaskets andthreaded entrance
- Plugged drain holes in each endshield for all angle mounting
- Internal corrosion resistant coatings on frame, base, endshields, rotor and stator
- USDA-approved, white epoxy RUST-OLEUM® paint
- UL Recognized, CSA Certified and CE Mark
Close-Coupled Pump, JM, Three Phase Dripproof, C-
- NEMA JM pump shaft dimensions
- JMV frame includes drip cover for vertical mount without base
- JM frame has rigid base, drip cover not included
- Ball bearings, mechanically locked on shaft end
- Continuous duty
- 1.15 Service Factor
- UL Recognized and CSA Certified
- UL Listed for Fire Pump applications (except as noted)
Fire Pump, Three Phase Dripproof, Rigid Base
- UL File EX5190, CSA File LR2025 and CE Mark
- Ball bearings
- 1.15 Service Factor
- Red paint on 25 HP through 200 HP
- NEMA Design B, Code G or less
- Dual voltage motors have 12 leads, suitable for wye-delta or across the linestart on either voltage, or part winding start on low voltage
- Single voltage motors have 12 leads and are suitable for wye-delta, acrossthe line, or part winding start
- Will accept C- Face kits, see Accessories section
- 230/460 and 460 Volt models rated for 50 HZ at next lower HP, 1.15 SF as noted
Fan and Blower - Direct Drive, PSC, Open Air Over Belly Band Thru-Bolt, Double Shaft
- Open frame and brackets
- Multi-speed capability
- Automatic reset thermal protector
- 30” leads• CCW rotation, fixed lead end
- 1” extended Thru-bolts both ends
- 20” overall length
- Length adapter kits included where noted
- Ball bearings
- UL Recognized and CSA Certified
- Capacitor not included, see Accessories section
