Profile

• Size Range: 1" through 24" pipe and insulation thickness of 1" through 4"
• Material: Carbon steel
• Finish: Plain or Hot-Dip Galvanized with Zinc Plated Bolts & Nuts
• Service: For maintaining alignment of piping through its axial expansion andcontraction cycles. Normally, two or more pipe alignment guides are usedon a single piping run to avoid a pivoting effect within the piping system.It is recommended that the first guide be located a maximum of four pipediameters from an expansion joint. The second guide should be placed amaximum of 18 pipe diameters from the expansion joint. Additional guidesshould be employed in accordance with the guide spacing data on next page.Supports are usually required between the intermediate guides to complywith standard support practice.

Features
• Pre-engineered to save calculation and installation time.
• PTFE slide bearing pads are composed of 100% virginPolytetrafluoroethylene polymer.
• Capable of supporting constant loads up to 2000 PSI at 70° F
• Coefficient of friction typically ranges between 0.06 and0.2 depending on bearing surface area, bearing load (sampleranges shown in chart for given pressures at 70˚F). Consultyour Anvil representative for further information. The lowcoefficient of friction for the PTFE slide assemblies permitsa smooth, unrestrained movement of the pipe and reduces overturning movements on supporting structures
.• PTFE is chemically inert and resists attack by chemicals, humidity and other elements found in harsh environments providedthat the steel supports are suitably protected
.• Self-lubricating, maintenance-free
.• Provides resistance to galvanic corrosion between pipe and support structure.

• Size Range: 2" through 24"
• Material: Carbon steel
• Finish: Plain or Hot-Dip Galvanized with Zinc Plated Bolts & Nuts
• Maximum Temperature: Plain 750° F, Galvanized 450° Ffor carbon steel pipe only

• Ordering: Specify figure number, pipe size, name and finish.

• Size Range: Service Pipe: 21/2" through 8" Sch. 10 and Sch. 40 IPSService Pipe: 21/2" through 6" FM 
• Approved Flow PipeBrace Pipe: 1" or 11/4" Sch. 40 IPS
• Material: Carbon steel
• Finish: Plain or Zinc Plated (Hot-Dip Galvanized optional)
• Service: Used to rigidly brace piping systems subjected to sway and seismic disturbances.Pipe clamp component of Anvil's 700 series sway brace assembly. Utilized only as a lateralbrace clamp.
• Approvals: FM Approved (FM 1950:2010). Complies with seismic bracing requirements of NFPA-13.Office of Statewide Health Planning and Development (OSHPD) State of California approved.
• Features:• Used to brace schedules 10 IPS, 40 IPS, and Flow pipe• Field adjustable design requires no threading of bracing pipe• Can be used as a component of a four-way brace support• Brace clamp design for installation of brace pipe above or below horizontal service pipe.

• Size Range: Structural Steel: Minimum Thickness – 1/8" (FM), 3/16" (UL), Maximum Thickness – 3/4"Service Pipe: 1" through 8"
• Material: Ductile iron beam attachment, shear head bolts and hex head mounting bolt
• Finish: Plain or Zinc Plated (Hot-Dip Galvanized optional)
• Approvals: UL and ULC Listed (UL 203A:2009), and FM Approved (FM 1950:2010). Complieswith seismic bracing requirements of NFPA-13. Office of Statewide Health Planning andDevelopment (OSHPD) State of California approved.
• Features:• Permits secure quick connection to structural members where drilling and/or welding of brace connection is not allowed oris not easily accomplished• Shear head bolt design ensures that the proper installation torque is accomplished for a tight non-slip fit to the structural member.• Bar joist beam attachment is designed for concentric loadings of seismic connections and fasteners

The Upthrust is for support of piping or equipment from below.It has a base flange for fastening to the floor or beams. Theload is supported during hydrostatic testing by means of (4)positioning studs. After testing the nuts are moved to eitherend of the stud to prevent interference during operation.The Upthrust constant support is available for loadsup to 24,463 (lbs). Corrosion resistant units are availableeither galvanized or carbon-zinc painted

• Size Range: 3⁄4" thru 2" Swivel Ring Hanger, Figure 69
• Material: Carbon steel
• Finish: Zinc Plated (Hot-Dip Galvanized optional)Service: Designed to be used with Anvil Figure 69, Adjustable Swivel Ring Hanger, for bracingsteel service pipe against up thrust during a seismic disturbance or sprinkler head activation.
• Approvals: UL and ULC Listed (UL 203A:2009). Complies with seismic bracing requirements of NFPA-13.
• Features:• One universal size accommodates ring hangers from 3/4" to 2".• Quick and simple to install by just snapping the surge restrainer into a locking position ontothe ring hanger.

• Size Range: Available in four sizes to take loads to 20,700 (lbs).All sizes provide for 12" of horizontal travel.
• Approvals: Complies with ANSI/MSS SP-69 and MSS SP-58(Type 58).
• Features:• Highly economical• Minimum friction• Virtually dust proof• Compact – designed for minimum head room• Versatile
• Installation: Shipped ready for installation. Attach to thesupporting steel by welding around the frame.
• Ordering: Specify size number, figure number, name and “H”dimension, if required. Horizontal travelers will be designed forspecial loads, travels or dual directional travel upon request.

• Size Range: 3⁄8" through 2 1⁄2"
• Service: Used as a replacement to standard rear bracket load pin to facilitate easy removal attime of rebuild or testing. May be supplied with new orders, when specified.
• How to size: Select size consistent with load pin diameter for Fig. 200/201 or Fig. 3306/3307.
• Features:• Designed to sharply reduce the time necessary to remove a badly corroded conventionalpin and may also eliminate damage to the bushing and bracket assembly, particularly ifthe pin and bracket are corroded.• Minimizes “free play” between pin to pin
• .Ordering: Specify figure number, nominal pin size and name.
• Installation: Shipped assembled. Remove nuts and washer. Loosen sleeve on pin and installsleeve/pin. Re-install washer and one nut. Tighten hex nut to snug. Install second nut

• Size Range: 1/2" through 12" pipe and accommodates up to 2" of insulation.
• Material: Carbon steel with high impact glass reinforced polypropylene saddle andcarbon steel pipe spacer.
• Finish: Plain or Galvanized Clevis HangerService: Recommended for the suspension of stationary insulated chilled or hotwater pipe lines.
• Maximum Temperature: 40° F to 200˚ FApprovals: Dual Fire Ratings, UL E94 VO and ASTM E84 Class 1 25/60.
• Features: V-Block design cradles pipethrough out the entire erection process.Clevis bolt spacer included as standardkeeps the clevis lower strap from collapsing.Eliminates:• Wood blocks and standard shields• Costly calcium silicate inserts• Re-leveling of piping at eachindividual hanger after insulationis completed

• Size Range: 3⁄4" through 12"
• Material: Carbon steel
• Finish: Plain, Galvanized or Epoxy coated
• Service: Recommended for suspension of insulated stationary pipe lines.
• Maximum Temperature: Plain 650° F, Galvanized and Epoxy 450° F
• Approvals: Complies with Federal Specification A-A-1192A (Type 1)WW-H-171-E (Type 1), ANSI/MSS SP-69 and MSS SP-58 (Type 1).
• Installation: Hanger load nut above clevis must be tightened securely toassure proper hanger performance.
• Adjustment: Vertical adjustment is provided, varying with the size of theclevis. Tighten upper nut after adjustment.
• Features:• Designed for 2" of insulation on 3⁄4" through 1 1⁄2" pipe and 4" ofinsulation on 2" and larger pipe.• When properly installed, clevis bolt is outside the insulation
  

• Size Range: 3" through 24" ductile or cast iron pipe
• Material: Carbon steel
• Finish: Plain or GalvanizedService: Recommended for the suspension of stationary ductile iron or cast iron pipe
• .Approvals: Complies with Federal Specification A-A-1192A (Type 1)WW-H-171-E (Type 1), ANSI/MSS SP-69 and MSS SP-58 (Type 1).
• Installation: Hanger rod nut above clevis must be tightened securely to assureproper hanger performance.
• Adjustment: Vertical adjustment without removing pipe may be madefrom 1 15⁄16" through 3 3⁄16", varying with the size of the clevis. Tighten uppernut after adjustment.
• Ordering: Specify pipe size, figure number, name and finish
• .Note: Figure 590 sizes 12" and below typically feature a Figure 260 Top Component.